27256 EPROM DATASHEET PDF

Full text of “IC Datasheet: EPROM” Jameco Part Number M NMOS Kbit (32Kb x 8) UV EPROM NOT FOR NEW DESIGN □ FAST. datasheet, pdf, data sheet, datasheet, data sheet, pdf, General NMOS K 32K x 8 UV EPROM Others with the same file for datasheet. (EPROM). The device is organized as 32K words by 8 bits (32K bytes). Accessing individual bytes from an address transition or from power-up (chip enable pin.

Author: Meztizuru Kajira
Country: Poland
Language: English (Spanish)
Genre: Marketing
Published (Last): 11 April 2014
Pages: 200
PDF File Size: 5.11 Mb
ePub File Size: 15.67 Mb
ISBN: 741-6-20424-127-4
Downloads: 57604
Price: Free* [*Free Regsitration Required]
Uploader: Mikazil

Output Enable G is the output control and epro be used to gate data to the output pins, inde- pendent of device selection. The integrated dose i.

Specifications mentioned in this publication are subject to change without notice. The magnitude of the transient current peaks is dependent on the capacitive and inductive loading of the device at the 27265. The length of the Over-program Pulse varies from 2. No license is granted by implication or otherwise under any patent or patent rights of STMicroeiectronics.

eprom datasheet & applicatoin notes – Datasheet Archive

Although only “Os” will be programmed, both “1 s” and “Os” can be present in the data word. These are stress ratings oniy and operation of the dstasheet at these or any other conditions above those indicated in the Operating sections of this specification is not implied.

A high level E input inhibits the other Ms from being programmed. To activate this mode, the programming equipment must force The recommended erasure procedure for the M is exposure to short vyave ultraviolet light which has wavelength A.

  CARE DRHP PDF

If the M is to be exposed to these types of lighting conditions for extended periods of time, it datashdet suggested that opaque lables be put over the M window to prevent unintentional erasure. All other address lines must be held at Vil during Electronic Signature mode. The only way to change a “0” to a “1 ” is by ultraviolet light erasure. When parallel programming several devices which share the common bus, Vpp should be lowered to Vcc 6V and the normal read mode used to exe- cute a program verify.

The associated transient voltage peaks can be sup- pressed eeprom complying with the two line output control and by properly selected decoupling ca- pacitors.

27256 – 27256 256K EPROM Datasheet

The transparent lid allows the user to expose the chip to ultraviolet light to erase the bit pattern. Except for E, all like inputs including G of the parallel M may be common. For further information on any aspect of dataxheet device, please contact STMicroelectronics Sales Office nearest to you.

Program Verify A verify should be performed on the programmed bits to determine that they were correctly pro- grammed. Vcc must be applied simultaneously with satasheet before Vpp and removed simultaneously or after Vpp.

Standby Mode The M has a standby mode which reduces the maximum active power 72256 from mA to datasheett. When in the standby mode, the outputs are in a high impedance state, independent of the G input.

The levels required forthe address and data inputs are TTL. Search the history of over billion web pages on the Datasjeet. The supply current, Ice, has three segments that are of interest to the system designer: Data s available at the ojjtputs after the falling edge of G, assuming that E has been low and the ad- dresses have been stable for at least tAvav-tcLov.

  LEY NO 26549 PDF

This mode is intended for use by programming equipment for the purpose of automatically matching the device to be programmed with its corresponding programming algorithm.

Full text of “IC Datasheet: EPROM”

It is recommended that a 1 j. STIVIicroelectronics products are not authorized for use as e;rom components in life support devices or systems without express written approval of STMicroeiectronics.

For the STMi- croelectronics M, these two identifier bytes are given below.

Up to 25 one-millisecond pulses per byte are provided for before the over program pulse is applied. The duration of the initial E pulse s is 1 ms, which will then be followed epom a longer over- program pulse of length 3ms by n n is equal to the number of the initial one millisecond pulses applied Table 3. Two identifier bytes may then be sequenced from the device outputs by datasheef address line AO from Vil to Vih.

Full text of ” IC Datasheet: Some lamps have a filter on their tubes which should be re- moved before erasure.