AGMA 923-B05 PDF

(This Information Sheet is NOT an AGMA Standard). American Gear Metallurgical Specifications for Steel Gearing Manufacturers AGMA B05 CAUTION. (This Information Sheet is NOT an AGMA Standard). American Gear Metallurgical Specifications for Steel Gearing Manufacturers AGMA B05 Association. AGMA B05 Metallurgical Specifications for Steel Gear – Download as Word Doc .doc /.docx), PDF File .pdf) or read online. AGMA B05 Metallurgical.

Author: Nikolar Duktilar
Country: Mozambique
Language: English (Spanish)
Genre: Business
Published (Last): 24 August 2005
Pages: 127
PDF File Size: 19.44 Mb
ePub File Size: 14.69 Mb
ISBN: 665-2-77809-605-1
Downloads: 71414
Price: Free* [*Free Regsitration Required]
Uploader: Doulkree

Gear Design Relevant Cleanness Metrics | Gear Solutions Magazine Your Resource to the Gear Industry

It is important to point out that the SEV value is useful in considering what the largest likely inclusion in the steel is, but it does not provide information about the number density of inclusions that exceed a critical value.

Characteristics covered include raw material, heat treatment and post heat treat processing, 923b05 their associated inspections. Characteristic1 2 21 22 Not specified. This method of steel cleanness rating has been used for decades in order to assure the level of steel cleanness is achieved per agmx specified limit. This bainite is the result of slower heat extraction rates due to part section size, mass of furnace load, marginal agitation, elevated quenchant temperatures, and generally follows alloy segregation and material flow lines.

Retained austenite is not included in the quantitative metallographic measurement 923–b05 non–martensitic structures.

The significance and interpretation of those results needs to be agreed upon between the parties. For carburize and hardened gearing or nitrided gearing, a 923-05 coupon used primarily to monitor the consistency of the heat treatment process in terms of carbon or nitrogen penetration and case microstructure.

  EDWARD MUSIA INSTALACJE I URZDZENIA ELEKTROENERGETYCZNE PDF

The introduction of nascent nitrogen into a suitable solid ferrous alloy by holding at a suitable temperature in contact with a nitrogenous material.

Gear Design Relevant Cleanness Metrics

Any post–heat treat stock removal must be considered. G H representative test coupon: Suggestions for improvement of this information sheet will be welcome. The preferential oxidization of certain alloying elements along grain boundaries during gas carburizing.

The ability to fully characterize the geometric and chemical characteristics of micro and macro oxide inclusion populations using automated image analysis SEM allows the steelmaker to understand how practices employed in the melting and teaming pouring and solidification of the steel affect oxide cleanness. Type Fine Thick A sulfide 2. For each heat treatment method and AGMA grade number, acceptance criteria are given for various metallurgical characteristics identified in this document.

The material must have adequate hardenability for the required hardness and section size combination for the required core hardness to be achieved. Any of the following methods are acceptable Should meet the following surface related characteristic: Acceptable if does not exceed: Please first log in with a verified email before subscribing to alerts.

Either the flat bottom hole or back reflection method may be used. For bar stock 923-n05 forged shafting including step shafts for solid on shaft pinion blanks as in figure 5: For nitriding specifications surface hardness is typically used rather than case hardness. A steel containing specified quantities of alloying elements other than carbon and the commonly accepted amounts of manganese, copper, silicon, sulfur, and phosphorus added to increase hardenability and to affect changes in mechanical properties.

  JAGGED ALLIANCE 2 KOMPLETTLSUNG PDF

Murakami proposes that a 30, mm 2 be used, which equates to a reduced variate value of 5. Adsorption of carbon processes involve a subsequent quenching to harden, while adsorption of nitrogen does not require quenching to harden. At this time, the Ultrapremium practice and certification limits with steels are produced using bottom-poured ingots. For carburized gearing the maximum depth of xgma carbon.

Quantitative stereography can be employed to convert the measured area concentration of inclusions to mean-free path between inclusions and volumetric concentration, enabling the gear design engineer to make direct comparisons of stressed volumes and volumetric inclusion concentrations.

AGMA 923-B05

The ability to characterize the 923b-05 of inclusion populations is critical to developing a strong understanding of how steelmaking practices affect the generation of inclusions.

A hard compound of iron and carbon, known chemically as iron carbide, having the chemical formula Fe3C. Mean-free path can quickly be used to consider the likelihood of an inclusion being present in a component and is valid for both globular oxides and stringers.

The inset pictures from the gear failure illustrate how this LEFM data relates to the gear failure. The data presented in Figure 3 meet these criteria. A representative test coupon may contain a tooth form that will be used to verify the heat treat process.

The hardness measured 923b05 on the functional surface, after appropriate surface preparation. Log into your account.