CISCO MDS 9124 CONFIGURATION GUIDE PDF

Example Cisco MDS Switch Default Port License Configuration. switch# show port-license Available port activation licenses are 0. Cisco MDS Family Quick Configuration Guide. OL Using the Switch Setup Utility Verifying the Module Status CHAPTER. 3. Configuring. Note If a Cisco MDS or switch is used as a core switch, only a nontrunking F PortChannel is supported. Trunking is not supported on.

Author: Yorisar Maull
Country: Anguilla
Language: English (Spanish)
Genre: Politics
Published (Last): 26 April 2009
Pages: 65
PDF File Size: 16.71 Mb
ePub File Size: 11.4 Mb
ISBN: 660-3-66687-255-3
Downloads: 99088
Price: Free* [*Free Regsitration Required]
Uploader: Necage

This is not correct. From time to time I will blog about other things of interest. This is not true. I am not sure if this is valid. Page Document states: In this case, using the proxy initiator mode simplifies the configuration.

It is worded as if it is a requirement but it is in fact not. The autoreconfigure option takes immediate effect at runtime. This is very redundant and can be combined into one bullet. You do not need to restart the fcdomain. You cannot mix ingress and egress interfaces in the same SPAN session.

If you assign port number for physical portshow can you assign for ports ? If you enabled the autoreconfigure option on both switches before connecting the fabric, a disruptive reconfiguration RCF will occur. Then states two bullets later: The way its written sounds like if you have a large scale deployment where you need explicit LUN access control you can use proxy-initiator, but its really the opposite.

Obviously there was a part of this paragraph that got chopped off somewhere. You must be logged in to post a comment. I am not sure that the statement in bold is correct. This page incorrect states that fcns reject-duplicate-pwwn is disabled by default.

  JBL GTO1514 PDF

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata

I think what is meant here is: A disruptive reconfiguration may affect data traffic. If a domain is currently isolated due to domain overlap, and you later enable the autoreconfigure option on both switches, the fabric continues to be isolated. Page shows with 8 base ports 8 licensed for growth.

You can nondisruptively reconfigure the fcdomain by changing the configured domains on the overlapping links and getting rid of the domain overlap. About System Message Logging properly configured system message logging server. If you do not need explicit LUN access control, configuation the proxy initiator mode simplifies the configuration. Cisco Documentation team has internally re-written this as: This situation can require several configuration tasks for each iSCSI host.

Should be 8 base ports, which can goto 8 or 16 additional ports. This can mean several configuration tasks for each iSCSI host.

Previous blog entries also dealt with storage, compute, virtualization and professional services. IP configuratiob does not have to be enabled, unless there is a specific topology where IP routing is necessary.

These pages talk about an active mode of fcanalyzer. Should say Step 1 Enable the mgmt 0 interface. Testing indicates that this is in fact enabled by default. Proudly powered by WordPress. Page Figure shows incorrect ip default-gateway Page States in one bullet: Reconfiguration as in changing of domains is always disruptive.

guive This should be made more clear. This however would be very nice to have in the documentation for IPS network simulator, an example showing complete configuration of Gigabit Ethernet interfaces and FCIP tunnels to go along with the Network Simulator. The default authentication port is Leave a Reply Cancel reply You must be logged in to post a comment. I am not sure. You basically give the same settings for the IBM blade switch but this is a 24 port not a 20 port.

  BRACHIAL PLEXOPATHIES CLASSIFICATION CAUSES AND CONSEQUENCES PDF

Certainly there is either a mistake in the wording or the example. When you join two switches belonging to two different stable fabrics that have overlapping domains, the following cases apply: FCIP uses different ports. On the same page I find this block of text very vague and confusing: Caution The span drop-threshold can be changed only if no span sessions are currently active on the switch. Although it can be configured it has no effect. This blog is mostly about my pursuits in Data Science.

Page Information is repeated twice on the same page: The opinions expressed in this blog are entirely my own and should not be taken as the opinion of my employer.

Unofficial Cisco MDS Release 3.x CLI Config Guide Errata – Maximum Entropy

Have a few different people read that and I think you will see where I am coming from. This page incorrectly states that you can disable password verification with aaa authentication login none command.

This is not correct as this does not work.