DATASHEET 2N2219 PDF

The 2N, 2N, 2N and 2N are sili- con planar TO (for 2N and 2N) and in Jedec . This datasheet has been download from. Semelab encourages customers to verify that datasheets are current before Test Conditions. Min. Typ. Max. Unit. LAB. SEME. 2N IC = 10mA. IB = 0. Sep 2. Philips Semiconductors. Product specification. NPN switching transistors. 2N; 2NA. FEATURES. • High current (max.

Author: Malakasa Arashilrajas
Country: Guatemala
Language: English (Spanish)
Genre: Health and Food
Published (Last): 17 November 2018
Pages: 477
PDF File Size: 3.34 Mb
ePub File Size: 9.9 Mb
ISBN: 749-3-12079-636-2
Downloads: 27396
Price: Free* [*Free Regsitration Required]
Uploader: Kagal

So the value if R B will be. In our case for a collector current of mA we have to pass a base current of 16mA. So to calculate the resistor value of the base we can use the formulae. Amplifier modules like Audio amplifiers, signal Amplifier etc.

When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV. Complete Technical Details can be found at the datasheet given at the end of this page. TL — Programmable Datasueet Voltage. As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to 2n2219 it on.

Philips – datasheet pdf

The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. Where Vcc is the voltage on which the load dataheet and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1.

  DOUBLE CROSS MALORIE BLACKMAN PDF

The 2N is a NPN transistor and is normally used as dataxheet switch in many circuits. Submitted by admin on 21 June When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. This resistor is connected to the base pin of the transistor to limit the current flowing through the base. Current flows in through collector, normally connected to load.

Current Drains out through emitter, normally connected to ground.

To make this current flow through the transistor the value of base current I B can be calculated using the below formula: Another important thing to keep in mind, while using a transistor as switch is the base resistor.

So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project.

But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle.

To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin. Where h FE, is the current gain of the transistor which in our case is The value of this current can be calculated by the required amount of current that will be consumed by the load.

  CHIFFREMENT AFFINE PDF

Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits. But this calculation will lead to the closest datashee to start with.

Here lets us assume the load here consumes around mA maximum so our collector current I C mA. However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor.

2N2219 Datasheet, Equivalent, Cross Reference Search

Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below. This stage is called Saturation Region.

To make this current flow through the transistor the value of base current I B can be calculated using the below formula:.