EP2C5TC8N from Altera Corporation. Find the PDF Datasheet, Specifications and Distributor Information. EP2C5TC8N IC CYCLONE II FPGA 5K TQFP Altera datasheet pdf data sheet FREE from Datasheet (data sheet) search for integrated. Device Family Data Sheet. This section provides information for board layout designers to successfully layout their boards for Cyclone™ II.

Author: Mikarr Goltiramar
Country: Ukraine
Language: English (Spanish)
Genre: Literature
Published (Last): 21 December 2005
Pages: 31
PDF File Size: 1.65 Mb
ePub File Size: 11.34 Mb
ISBN: 258-3-38505-913-2
Downloads: 12817
Price: Free* [*Free Regsitration Required]
Uploader: Felrajas

Revision History Refer to each chapter for its own specific revision history. For information on when each chapter was updated, refer to the Chapter Revision Dates section, which appears in the complete handbook.

Altera Corporation Section I. Cyclone II Architecture Chapter 3. Reference designs, system diagrams, and IP, found at www. The EP2C5A ep2c5t1448n only available in the automotive speed grade. Altera Corporation February — — — — — — — — A programmable register A carry chain connection A register chain connection The ability to drive all types of interconnects: LUT for unrelated functions.

When using register packing, the LAB-wide synchronous load control signal is not available. LEs datasheef normal mode support packed registers and register feedback. The Altera Corporation February Register feedback and register packing are supported when LEs are used in arithmetic mode.

Figure 2—5 Figure 2—5. The LE directly supports an asynchronous clear function. Each LAB supports up to two asynchronous clear signals labclr1 and labclr2. These row resources include: Driving Left Notes to Figure 2—8: Cyclone II Device Handbook, Volume 1 Register chain interconnects within an LAB C4 interconnects traversing a distance of four daatsheet and down direction C16 interconnects for high-speed vertical routing through the device Figure 2—9 shows the register chain interconnects.

Altera Corporation February For LAB interconnection, a primary LAB or its LAB neighbor see interconnects can drive each other to extend their range as well as drive row interconnects for column-to-column connections. Table 2—1 Table 2—1. DPCLK[] pins are dual-purpose clock pins. There are four clock control blocks on each side.

Figures 2—11 and 2— The following sources can be inputs to a given clock control block: Internal logic can be datawheet to enabled or disabled the global clock network in user mode. IN Rp2c5t144c8n Corporation February IOE clocks are associated with row or column block regions. Only epp2c5t144c8n global clock resources feed to these row and column regions. The signal enables and disables the PLLs. The pfdena signal controls the phase frequency detector PFD output with a programmable gate.


Altera Datasheets – Waveshare Wiki

If the C2 output is not Altera Corporation February The M4K memory blocks include input registers that synchronize Memory writes and output registers to pipeline designs and improve system performance. The ep2c5t144c8 registers can be bypassed, but input registers cannot. This applies to both read and write operations. Altera Corporation February summarizes the features supported by the M4K memory.

Simultaneous read and write from an empty FIFO buffer is not supported. Description Altera Corporation February M4K block outputs can also connect to left and right LABs through each 16 direct link interconnects.

Altera Corporation February summarizes the different clock modes supported by the M4K Description In this mode, a separate clock is available for each port ports A and B The total number of multipliers for each device is not the sum of all the multipliers. The embedded multiplier consists of the following elements: Multiplier Modes Table 2—12 multipliers can operate in.

R4 Interconnects Embedded Multiplier Control 36 [ The Quartus II software automatically duplicates a single OE ep2c5t1448n that controls multiple output or bidirectional pins. You can use IOEs as input, output, or bidirectional pins. There are two paths available for combinational or registered inputs to the logic array. Each path contains a unique programmable delay chain. All registers share sclr and aclr, but each register can individually disable sclr and aclr.

Programmable delays decrease input-pin-to-logic-array and IOE input register delays. The Quartus II Compiler can program these delays to automatically minimize setup time while providing a zero hold time.

Cyclone II EP2C5 Mini Dev Board

The system clock is daatsheet to clock the DQS write signals, commands, and addresses. Figure 2—27 the dedicated circuitry to the logic array. Number of LVDS Channels 1 31 35 56 60 61 65 29 33 53 57 75 79 52 60 45 53 52 60 Altera Corporation February This also minimizes the need for external resistors in high pin count ball grid array BGA packages. When using on-chip series termination, programmable drive strength is not available.

A device operating in JTAG mode uses four required pins: File via an embedded processor. Manufacturer Identity 11 Bits and 3—3 show the 1, 1, 1, LSB 1 Bit Altera Corporation February Cyclone II devices are configured at system power-up with data stored in an Altera configuration device or provided by a system controller. The bank CCIO selects whether the configuration inputs are 1. The hot-socketing feature in Cyclone II devices offers the following: This condition can lead to latch-up and cause a low-impedance path from V a large amount of current, possibly causing electrical damage.


CC parameters will determine the initialization time. February Removed ESD section. Altera Corporation February ramp time requirement, you must CC shows the revision history for this document.

Additionally, device operation at the absolute maximum ratings for extended periods of time may have adverse effect on the device reliability. During transition, the inputs may undershoot to —2. This value is specified for normal device operation. The value may vary during power-up. This applies for all V settings 3. V ICM 3 The p — n waveform is a function of the positive channel p xatasheet the negative channel n. Adtasheet is sample-tested only. Capacitance is measured using time-domain reflectometry TDR.

Refer to typical I standby specifications. Timing Specifications You should select power supplies and regulators that can supply the amount of current required when designing with Cyclone II devices. The second rp2c5t144c8n represents the minimum timing parameter for commercial devices. Speed —8 Speed Grade Unit Grade 2 0. Speed —8 Speed Unit Grade Grade 2.

These numbers are for automotive devices. Peak-to-peak output jitter on high-speed PLLs. Lock time for high-speed transmitter and receiver PLLs. Refer to Figure 5—4 CO Figure 5—5. For extended temperature devices, the maximum data rate for x1 mode is Mbps. DCD for a clock is the larger value of D1 and D2. Duty Cycle Distortion DCD expressed in absolution derivation, for example Figure percentage, and the percentage number is clock-period dependent. DCD as a percentage is defined as: Therefore, any distortion on the input Figure 5—9.

For more information contact Altera Applications. Ordering Figure 6—1 information on a specific package, contact Altera Applications Elcodis is a trademark of Elcodis Company Ltd. All other trademarks are the property of their respective owners. Download datasheet 3Mb Share this page. Copy your embed code and put on your site: Prev Next This section provides information for board layout designers to.

Refer to each chapter for its own specific revision history. DC Characteristics ep2x5t144c8n Timing Specifications. Automotive-Grade Altera Corporation February —