HP33120A MANUAL PDF

Service Guide. Publication Number (order as manual set) The security code is set to “HP” when the function generator is. Note: Unless otherwise indicated, this manual applies to all Serial Numbers. The Agilent .. For information on using the Phase-Lock Option for the HP A. Microsoft® Windows® included. Agilent A. 15 MHz Function /. Arbitrary Waveform Generator. Note: Unless otherwise indicated, this manual applies to all .

Author: Malazuru Gardalar
Country: Norway
Language: English (Spanish)
Genre: Sex
Published (Last): 20 September 2011
Pages: 296
PDF File Size: 13.27 Mb
ePub File Size: 10.76 Mb
ISBN: 201-9-95164-481-2
Downloads: 29241
Price: Free* [*Free Regsitration Required]
Uploader: Dot

Output Minimum Maximum Function Termination Only one interface can be enabled at a time.

HP 33120A Manuals

The function generator will accept an internal modulating signal, an external modulating signal, or both. The output frequency is Output Frequency automatically adjusted if you select hp3312a0 function whose maximum continued frequency is less than that of the currently active function.

From the remote interface, you can also display a message containing up to 11 characters on the front panel. Used only in the internal triggered burst mode.

The function generator is shipped from the factory with a mAT fuse installed. Chapter 3 Features and Functions System-Related Operations Display Control To speed up the rate at which the function generator can make configuration changes, or for security reasons, you may want to turn off the front-panel display.

Page 32 Chapter 2 Front-Panel Menu Operation To output a modulated waveform To output a modulated waveform A modulated waveform consists of a carrier and a modulating waveform. Page 72 Chapter 3 Features and Functions Burst Modulation Burst Modulation You can configure the function generator to output a waveform with a specified number of cycles, called a burst.

Page 86 Chapter 3 Features and Functions Frequency Sweep Start Frequency and Stop Frequency The start frequency and stop frequency set the upper and lower frequency bounds for the sweep.

Comments to this Manuals Your Name. Page Chapter 3 Features and Functions System-Related Operations System-Related Operations This section gives information on topics such as power-down recall, self-test, error conditions, and front-panel display control.

  ALGORITMO 3DES PDF

Page Chapter manuaal Features and Functions System-Related Operations Display Control To speed up manuzl rate at which the function generator can make configuration changes, or for security reasons, you may want to turn off the front-panel display. Notice that the annunciator flashes, indicating that the displayed percentage is the depth also called percent modulation.

Don’t have an account? Chapter 3 Features and Functions Calibration Overview To Change the Security Code To change the security code, you must first unsecure the function generator, and then enter a new code. Page Chapter 3 Features and Functions Calibration Overview To Change the Security Code To change the security code, you must first unsecure the function generator, and then enter a new code.

Page 6 Quick Start Then, rotate the handle to the desired position. After one sweep from the start frequency to the stop frequency, the function generator waits for the next trigger while outputting the start frequency.

The function generator begins at the start frequency, sweeps to the stop frequency, and then resets back to the start frequency. Page 92 Group Execute Trigger message. Page 87 Chapter 3 Features and Functions Frequency Sweep Sweep Time The sweep time specifies the number of hp3320a required to sweep from the start frequency to the stop frequency. Quick Start One of the first things you will want to do with your function generator is to become acquainted with its front panel. Duty cycle is specified as a percentage and represents the amount of time per cycle that the square wave is maunal.

The output maanual is Output Amplitude automatically adjusted and no error is generated if you change the continued output termination. Page 28 Chapter 2 Front-Panel Menu Operation A front-panel menu tutorial Menu Example 2 The following example shows how to use hp331120a recall menu feature as a shortcut to set the command back to its original setting.

You are then exited from the menu. You can use sine, square, ramp, triangle, or arbitrary waveforms for the hop frequency waveshape. Certain combinations of burst count and carrier frequency are not allowed.

  EPHESIA GRAMMATA PDF

AM modulation is enabled. The duty cycle is auto- matically adjusted if you select a frequency that is not valid with the present duty cycle.

Chapter 3 Features and Functions System-Related Operations System-Related Operations This section gives information on topics such as power-down recall, self-test, error conditions, and front-panel display control. Page 48 Chapter 3 Features and Functions Output Configuration Output Frequency As shown below, the output frequency range manuql on the function currently selected.

HP A USER MANUAL Pdf Download.

Chapter 3 Features and Functions Output Configuration Output Amplitude As shown below, the output amplitude range depends on the function currently selected and the output termination. In amplitude modulationthe amplitude of the carrier is varied by the amplitude of the modulating waveform.

To recall the stored state, you must use the same memory location used previously to store the state. The following steps show you how to change hl33120a amplitude to 50 mVrms. Page IEEE interface and an interface.

Freq 1 Enable the frequency modify mode. At power-on, the units for output amplitude are volts peak-to-peak. The default is Sine. Page 20 Front-Panel Menu Operation Chapter 1 Quick Start To store the instrument state To store the instrument state You can store up to three different instrument states in non-volatile memory. The Front-Panel Menu at a Glance T he menu is organized in a top-down tree structure with three levels.

Chapter 1 Quick Start To output a stored arbitrary waveform To output a stored arbitrary waveform There are five built-in arbitrary waveforms stored in non-volatile memory for your use. Chapter 2 Front-Panel Menu Operation To output a modulated waveform To output a modulated waveform A modulated waveform consists of a carrier and a modulating waveform.

Use the knob and the arrow keys to modify the displayed number.