KURZWEIL K2600 MANUAL PDF

View and Download Kurzweil K introduction manual online. Kurzweil K : User Guide. K Electronic Keyboard pdf manual download. Also for. View and Download Kurzweil K Series service manual online. K Series Synthesizer pdf manual download. View and Download Kurzweil K quick start up manual online. Kurzweil K Quick Start. K Electronic Keyboard pdf manual download. Also for.

Author: Kazahn Nern
Country: Seychelles
Language: English (Spanish)
Genre: Education
Published (Last): 14 August 2009
Pages: 495
PDF File Size: 6.63 Mb
ePub File Size: 18.95 Mb
ISBN: 538-8-85259-897-5
Downloads: 15810
Price: Free* [*Free Regsitration Required]
Uploader: Samurr

Kurzweil is a product majual of Young Chang Co. All other products and brand names are trademarks or registered trademarks of their respective companies. A N D Music Corp. Box Lakewood, WA Tel: This chapter also includes a description of the models available in the K Series and a description of the symbols used throughout this manual.

Diagnostics Entering Diagnostics Entering Diagnostics 1. Apply power to the unit. When the message appears in the LCD, Please wait The LCD shows the following: Figure shows an example of the display for the Engine Blk test.

Engine Blk Please wait. Success Press any key to continue The LCD Test includes four test phases that run automatically. The four steps include the following: This test destroys all non-volatile user RAM! If you need instructions, refer to Saving User Data ,2600 page The FDD Init test recalibrates the disk drive. Sampling Opt Sampling Option Figure illustrates the kurwzeil menu of sampling option tests. To display this page, select Sampling Option from the main menu and use the Up or Down button or the Alpha Wheel to scroll through the menu options.

These sine waves are not sampled, but are merely used to generate digital data with which to test the digital audio circuitry. The kkurzweil checksum is compared to the checksum stored in ROM. In some instances a procedure may instruct you to remove a cable from an after-market option board or device that may not be present.

The top cover is secured to kurzweik KR with ten screws: Disconnect the cables listed in Table Be sure to set it safely aside so that you can reinstall it kuzweil you reconnect the cable.

To release mqnual DSP Board from the standoffs on the left side of the board, squeeze the top of the standoffs and slightly lift the left side of the DSP Board. Place the KR on its side.

Hold the CPU holding bracket and remove the holding bracket screw from the bottom enclosure. Remove the two screws that secure the MIDI jacks to the rear panel. Remove the screw manuual secures the CPU Board to the mounting post. Position the transformer over the mounting holes provided for it on the bottom enclosure. Install the four screws and split washers that secure the transformer to the bottom enclosure.

Disconnect the stranded wire cable that connects the ourzweil to the Power Supply Board. Remove the four screws that secure the fan to the rear panel. Place the Kirzweil on its side and remove the four screws along the bottom edge of the front panel cover.

  HUAWEI RTN 980 PDF

Tilt the front of the KR up and remove the three screws along the bottom edge of the front panel mounting bracket. If the unit you are servicing has a Sampling Board installed, the hardware that secured it was removed during the removal of the front panel cover.

Insert the front panel mounting bracket into the left side of the bottom enclosure. This is done to clear the top cover mounting holes on the left side.

Then slide the right side of the front panel mounting bracket. Secure the two cables to the disk drive mounting bracket with the tape. Remove the AC Entry Module. Replacing the AC Entry Module 1. Standing at the front panel, tilt the front end of the disk drive mounting manuwl down toward you and lower it into position.

From the Optical Inputs section of the front panel, remove the cap from the Optical jack. Refer to Figure Remove the enclosure support wall screws and the endblock locking bracket screws not the endblock screws. Dotted lines indicate the locations of the enclosure support wall screws. Arrows show the locations of the endblock locking bracket screws.

Arrows show the locations of the enclosure support wall k26000 endblock locking bracket screws. Remove the seven rear panel screws. These secure the rear panel portion of the top enclosure. Remove the four endblock screws. Turn the top enclosure over and place it face down onto your work surface. Replacing the Top Enclosure 1. Lift the top enclosure up and place it in position over the bottom enclosure.

Remember that the Audio Board extends beyond the rear panel. Following Steps 2 and 3 disconnect the cables listed in Table Place the enclosure support wall in position. Be sure that the mounting clip on the Sampling Board is positioned into the upper groove on the enclosure support wall.

Place the enclosure support wall in position and install the screws that secure it to the top enclosure. Press individual switch button caps to verify that their corresponding switches click.

Install the four screws that secure the Slider Board to the top enclosure. Place the enclosure support wall in position and install the enclosure support wall screws. You should see thread marks in the extrusion to verify proper positioning of the enclosure support wall screws. This cable is bent to form a loop.

If the unit you are servicing has a Sampling Board, follow the procedure on page to remove it. Install the enclosure support wall screws. If you are servicing a K, kurzdeil are seven screws securing the enclosure support wall. Start with the standoffs on the kurzwell side of the board.

  EXAMEN COPROPARASITARIO PDF

Kurzweil K2600 Series Service Manual

The Power Supply Board is secured to the bottom enclosure with four screws. Two screws are located at the left edge as viewed standing at the keyboard of the board; the other two are located at the heatsink mounting bracket. Place the fan in position over the standoffs provided for it on the bottom enclosure. Push the fan down so that the standoffs come up through the mounting holes of the fan. See page for the corresponding procedures for the KX note Keyboard Assembly. Removing the K Keyboard Assembly The following procedure assumes that the K is open and that you have followed the instructions on page to remove the top enclosure.

Slide the K back onto your work surface. This cable has nylon reinforced tape securing it to the bottom enclosure. Peel back the tape from one side to free the cable.

Follow the procedure for removing the keyboard page or disconnecting the keyboard page The following diagrams illustrate the outlines of the natural and sharp keys and the locations and functions of the components described in the following procedures.

KURZWEIL K INTRODUCTION MANUAL Pdf Download.

Each key has a spring located at the rear of the key. Using needle-nose pliers, slightly pull up the top portion of the spring to release it from the key. Be careful not to pull up too much, which could damage the spring. Always replace a sharp key before replacing the adjacent natural keys. Place the key on the keyboard chassis and lower the key into position.

Be sure that the keys are resting on a soft surface to avoid scratching or other damage. The keyboard is secured to the bottom enclosure using nine screws. Refer kanual Figure for the position of the screws.

Place the keyboard on the bottom enclosure. Then move the top of the dowel toward the front of the keyboard to remove the spring from the hook.

Pivot Keyboard chassis section The following instructions apply to both natural and sharp keys. Hook the front end of the key under the keyboard chassis.

The main components of the weighted-key action consist of the following: There are seven position brackets and one 4-position bracket. Place the rod and key weights into position over the support brackets and snap the rod into the support brackets.

Be certain that the rod is pressed securely into the support brackets. Prior to replacing the keys, check that each key weight moves freely.